KERUI Home Security System Review: Alarm Panel

Add Comment | Related Links | TrackBack
Related Content

KERUI Home Security System Review: Alarm Panel

to enable passcode at keyboard: go to system settings / password . scroll to keyboard lock. press 0 or 1 to disable / enable the keyboard lock then OK. nothing on keypad will do anything until you enter the code.

Loyd
Sun, 26 Jul 2015 04:40:55 +0400

Intelligent will require the device to trigger twice within 30 before alarming. It's mostly for motion sensors and owning pets large enough to trigger the motion sensor. I have two cats and the motion sensor never triggers for them. I'm assuming dogs would trigger. In that case, set the motion sensor to intelligent.

Steve
Thu, 10 Sep 2015 06:10:30 +0400

Insert a sim-card without pincode. If needed use a gsm-phone to change that. It will not work with a pincode!

fons
Sun, 08 Nov 2015 22:36:01 +0300

Does this alarm come with a UK charging plug?

Stuart
Tue, 09 Feb 2016 21:09:47 +0300

The system I purchased in the US does not come with a UK power plug.

Mel
Fri, 12 Feb 2016 22:57:10 +0300

A question to all of you, who have used the system for some time.
What is your impression regarding the stability (false alarms ?) and quality of the alarm system ?

Ken
Tue, 15 Mar 2016 00:44:27 +0300

I have never gotten a false alarm for no good reason. One time, the motion sensor kept tripping the alarm. When I got home I found that my kid's mylar balloon has floated in front of the sensor, causing it to trigger as it floated around the living room. Otherwise, haven't had false trips.

Mel
Tue, 15 Mar 2016 23:30:24 +0300

I have yet to see any mention of a time delay. If you only use the keypad or the RFID, once you open your home front door, you may trip a door sensor and/or a motion sensor. Do you have a time delay before the alarm sounds in order to put in your de-activate code?

What about for leaving, does it have a time delay before leaving?

Scott
Tue, 03 May 2016 00:15:03 +0400

The instruction manual says you can set a time delay from 0 to 99 seconds. I haven't tried it. I use the FOB remote, so never needed the time delay.

Mel
Tue, 03 May 2016 11:24:39 +0400

I have this alarm with 10 sensors attached. Each sensor = 1 zone. I would like to use "stay arm" function. All sensor zones are set to type "Normal". One zone 02 (sensor 2) is set to type "stay armed" for testing perpouses. Despite the fact I arm alarm in 'stay armed' mode all sensors are armed: for example motion sensor no 4 is tiggering the alarm.
Do you know what is wrong set?

Gabor
Wed, 23 Nov 2016 22:39:11 +0300

Everything is working right now. 'Stay armed' means 'sensor is not working when stay arm mode is turned on'. So I have to set sensor number 2 to normal type and others to 'stay armed'..not the other way arround.

Gabor
Thu, 24 Nov 2016 12:21:56 +0300

Regarding the intelligent mode i try it on windows/door switch, the sensor must be triggered 2 times to activate the alarm ( it works on armed and stay armed mode).

Ali
Tue, 27 Dec 2016 11:43:41 +0300

If any one enter the house and cut the power or remove sim card or smash the panel this will deactivate the system or not?

Ali
Mon, 16 Jan 2017 10:26:52 +0300

I think if you cut the power to it, then it will not be able to do anything. But to remove the SIM requires removing the back panel. When the back panel is removed while the system is armed, the alarm will go off. But if you just push the deactivate button before removing the back panel, then the alarm will not go off.

Mel
Tue, 17 Jan 2017 02:38:20 +0300

My Kerui has built in battery and is charged with USB. if there was a power cut there would be plenty of time to send sms message to your phone after the break in.

ig
Tue, 07 Mar 2017 04:55:11 -0800

Hi, I know this thread is rather old but I just bought a w18 alarm system and I am trying to figure out how to disarm it on the panel with a passcode. As you wrote you also hadn't had a clue, I am hoping since then you might have figured it out. Thanks.

Gabi
Sun, 10 Dec 2017 12:01:07 -0800

I have configured my system with a GSM LTE simm card. The systems works as it should and can be armed or disarmed by text. The instructions are a bit lacking but work if followed.

mlfox
Sat, 13 Feb 2021 16:25:51 -0800

Now that I have my system set up with a GSM sim card, does anyone know if the system capable of blocking select inbound text numbers? According to my phone carrier's records, my system is being texted by unauthorized "spam" texts.

mlfox
Fri, 19 Feb 2021 15:45:37 -0800

<< Back to Article

Add Comment | Related Links | TrackBack
Related Content

Did your message disappear? Read the Forums FAQ.

TrackBack

TrackBack only accepted from WebSite-X Suite web sites. Do not submit TrackBacks from other sites.

Send Ping | TrackBack URL | Spam Control

Title: KERUI Set-Up Questions
Weblog: GearHack
Excerpt: I am getting used to the Kerui system, however, it is not really intuitive. Have some questions, maybe some of you can help me: 1. I have attached a K16 wireless keypad, anyone know how to change standard password? 2. Zone concept: A remote is added to a zone, but a remote cannot be mount to more th . . .
Tracked: Sun, 31 Jul 2016 09:44:28 +0400

Title: KERUI G18 SMS Problem and Questions
Weblog: GearHack
Excerpt: Ok I have a 2-in-1 question, I bought the G18, but now and then it doesnt send out sms to all the listed numbers (I have 4 numbers programmed). Sometimes it only sends to 1 or 2 numbers...... Secondly, what are the CID number and MCS numbers? Im struggling to understand that part. Any help will be a . . .
Tracked: Thu, 01 Jun 2017 22:09:29 -0700

Add Comment

Spam Control | * indicates required field

Messages, files, and images copyright by respective owners.

Back to Article

Fun for Photographers

Get Our

Memecoins!

Fun for Photographers